Assembly guide
SAFI TV bench
TV bench 200, 2 doors + 2 drawers + open niche · 2000 × 400 × 420 mm · Item number safi-tv-bench-200
Before you start
- About 2 h 15
- Two people needed
- 2 packages
Tools
- Cross-head screwdriver
- Mallet, or a hammer and a wood block
Parts
Every part carries its letter. Check everything is there before you start.
| Ref. | Part | Size (mm) | Qty |
|---|---|---|---|
| A | Side panel left | 420 × 380 × 18 | 1 |
| B | Side panel right | 420 × 380 × 18 | 1 |
| C | Top panel | 1964 × 380 × 18 | 1 |
| D | Bottom panel | 1964 × 380 × 18 | 1 |
| E | Back panel | 1978 × 338 × 3 | 1 |
| F | Divider 1 (left half) | 367 × 324 × 18 | 1 |
| G | Divider 1 (right half) | 367 × 324 × 18 | 1 |
| H | Divider 2 (left half) | 367 × 324 × 18 | 1 |
| I | Divider 2 (right half) | 367 × 324 × 18 | 1 |
| J | Divider 3 (left half) | 367 × 324 × 18 | 1 |
| K | Divider 3 (right half) | 367 × 324 × 18 | 1 |
| L | Divider 4 (left half) | 367 × 324 × 18 | 1 |
| M | Divider 4 (right half) | 367 × 324 × 18 | 1 |
| N | Door left-hinged | 374 × 358 × 18 | 1 |
| O | Drawer front | 373 × 358 × 18 | 2 |
| P | Drawer side | 350 × 220 × 18 | 4 |
| Q | Drawer sub-front | 279 × 220 × 18 | 2 |
| R | Drawer back | 279 × 206 × 18 | 2 |
| S | Drawer bottom | 339 × 293 × 3 | 2 |
| T | Door right-hinged | 374 × 358 × 18 | 1 |
| U | Plinth front (recessed 30) | 1964 × 60 × 18 | 1 |
| V | Plinth back | 1964 × 60 × 18 | 1 |
Hardware
All supplied, in bags.
- ×4Cup hinge Ø35, 110°, soft-close, full overlay, with clip plate
- ×8Euro screw 6.3×13 (hinge plates)
- ×8Chipboard screw 3.5×16, pan head
- ×2Ball-bearing drawer slides, 45 mm, ¾ extension (pair)
- ×12Beech dowel Ø8×35, fluted
- ×34Chipboard screw 4×30, countersunk
- ×4Felt pad Ø28
- ×44Cam lock Ø15 + screw-in bolt (drilling distance 24 mm)
- ×44Cam cover cap Ø15, matching colour
Steps
- 1
Prepare
Open the boxes on a rug or flattened cardboard. Sort the parts by letter and check them against the list.
- 2
Build the frame
Push the dowels and cam bolts into their holes. Join the sides, top, bottom and dividers, then turn each cam lock a quarter turn.
Parts
Hardware
- 3
Fit the base
Screw the base under the frame, lining up its edges before tightening.
Parts
- 4
Fix the back
Lay the frame flat, check it is square by measuring both diagonals, then screw the back panel all round.
Parts
Hardware
- 5
Build the drawers
Assemble each drawer box, slide the bottom into its groove and screw on the front. Screw the runners into the cabinet, then slide the drawers in.
Parts
Hardware
- 6
Hang the doors
Screw the hinges to the doors, clip them onto their plates, then align the doors with the hinge screws.
Parts
Hardware
- 7
Finishing
Fit the screw and cam covers, the felt pads and the accessories.
Hardware
A part missing or damaged?
Send us a photo on WhatsApp with your reservation number and we send the replacement part.