Assembly guide
QAWS TV bench
TV bench 160, flap + drawer + open niche · 1600 × 400 × 480 mm · Item number qaws-tv-bench-160
Before you start
- About 1 h 45
- Two people needed
- 2 packages
Tools
- Cross-head screwdriver
- Mallet, or a hammer and a wood block
Parts
Every part carries its letter. Check everything is there before you start.
| Ref. | Part | Size (mm) | Qty |
|---|---|---|---|
| A | Side panel left | 480 × 380 × 18 | 1 |
| B | Side panel right | 480 × 380 × 18 | 1 |
| C | Top panel | 1564 × 380 × 18 | 1 |
| D | Bottom panel | 1564 × 380 × 18 | 1 |
| E | Back panel | 1578 × 328 × 3 | 1 |
| F | Divider 1 (left half) | 367 × 314 × 18 | 1 |
| G | Divider 1 (right half) | 367 × 314 × 18 | 1 |
| H | Divider 2 (left half) | 367 × 314 × 18 | 1 |
| I | Divider 2 (right half) | 367 × 314 × 18 | 1 |
| J | Drop-down flap | 560 × 348 × 18 | 1 |
| K | Arched niche facade (fixed) | 473 × 348 × 18 | 1 |
| L | Drawer front | 560 × 348 × 18 | 1 |
| M | Drawer side | 350 × 220 × 18 | 2 |
| N | Drawer sub-front | 465 × 220 × 18 | 1 |
| O | Drawer back | 465 × 206 × 18 | 1 |
| P | Drawer bottom | 479 × 339 × 3 | 1 |
| Q | Plinth back | 1564 × 130 × 18 | 1 |
| R | Centre support (recessed 206) | 136 × 130 × 18 | 2 |
Hardware
All supplied, in bags.
- ×1Flap / tilt door hinge pair with stay
- ×4Euro screw 6.3×13 (hinge plates)
- ×8Chipboard screw 3.5×16, pan head
- ×1Ball-bearing drawer slides, 45 mm, ¾ extension (pair)
- ×12Beech dowel Ø8×35, fluted
- ×19Chipboard screw 4×30, countersunk
- ×8Felt pad Ø28
- ×28Cam lock Ø15 + screw-in bolt (drilling distance 24 mm)
- ×28Cam cover cap Ø15, matching colour
Steps
- 1
Prepare
Open the boxes on a rug or flattened cardboard. Sort the parts by letter and check them against the list.
- 2
Build the frame
Push the dowels and cam bolts into their holes. Join the sides, top, bottom and dividers, then turn each cam lock a quarter turn.
Parts
Hardware
- 3
Fit the base
Screw the base under the frame, lining up its edges before tightening.
Parts
- 4
Fix the back
Lay the frame flat, check it is square by measuring both diagonals, then screw the back panel all round.
Parts
Hardware
- 5
Build the drawers
Assemble each drawer box, slide the bottom into its groove and screw on the front. Screw the runners into the cabinet, then slide the drawers in.
Parts
Hardware
- 6
Hang the doors
Screw the hinges to the doors, clip them onto their plates, then align the doors with the hinge screws.
Parts
Hardware
- 7
Finishing
Fit the screw and cam covers, the felt pads and the accessories.
Hardware
A part missing or damaged?
Send us a photo on WhatsApp with your reservation number and we send the replacement part.